diff options
Diffstat (limited to 'robot/mode_grid.c')
| -rw-r--r-- | robot/mode_grid.c | 462 |
1 files changed, 461 insertions, 1 deletions
diff --git a/robot/mode_grid.c b/robot/mode_grid.c index 8526499..e36162e 100644 --- a/robot/mode_grid.c +++ b/robot/mode_grid.c @@ -1,3 +1,463 @@ #include "mode_grid.h" -void w2_mode_grid() {} +void w2_mode_grid() { + + initialize(); //only keep this when using this module on its own + + set_motors(0,0); + + //int gridMode = 0; //robot is in the grid + + //coordinates of the orders + orderOne(); + orderTwo(); + orderThree(); + orderFour(); + + beginLocation(); + + for (int i = 0; i < 4; i++ ){ + + destination.x = order[i].x; + destination.y = order[i].y; + + locationMessage(); + delay(1000); + + if (location.x != destination.x ){ + while(location.x != destination.x ){ + if (location.x > destination.x){ + turn_West(); + gridFollowLine(); + grid_crossway_detection(); + location.x--; + locationMessage(); + if (location.x == destination.x){ + arrivedMessage(); + } + } + + else if(location.x < destination.x){ + turn_East(); + + gridFollowLine(); + grid_crossway_detection(); + location.x++; + locationMessage(); + if (location.x == destination.x){ + arrivedMessage(); + } + } + } + } + + if (location.y != destination.y ){ + while(location.y != destination.y ){ + if (location.y > destination.y){ + turn_South(); + gridFollowLine(); + grid_crossway_detection(); + location.y--; + locationMessage(); + if (location.y == destination.y){ + arrivedMessage(); + } + } + + else if(location.y < destination.y){ + turn_North(); + gridFollowLine(); + grid_crossway_detection(); + location.y++; + locationMessage(); + if (location.y == destination.y){ + arrivedMessage(); + } + } + } + } + } +} + +void full_rotation(){ + delay_ms(500); + set_motors(60,-60); + delay_ms(540); + set_motors(0,0); + position = read_line(sensors,IR_EMITTERS_ON); + delay_ms(500); +} + +void grid_rotation_left(){ + delay_ms(500); + set_motors(-30,30); + delay_ms(600); + set_motors(0,0); + position = read_line(sensors,IR_EMITTERS_ON); + delay_ms(500); +} + +void grid_rotation_right(){ + delay_ms(500); + set_motors(30,-30); + delay_ms(600); + set_motors(0,0); + position = read_line(sensors,IR_EMITTERS_ON); + delay_ms(500); +} + +void grid_crossway_detection(){ + set_motors(0,0); + set_motors(50,50); + delay_ms(150); //150 + set_motors(0,0); + position = read_line(sensors,IR_EMITTERS_ON); + delay_ms(500); +} + +//variation on "void w2_mode_maze()" +void gridFollowLine(){ + unsigned int last_proportional=0; + long integral=0; + + // This is the "main loop" - it will run forever. + while(1) + { + // Get the position of the line. Note that we *must* provide + // the "sensors" argument to read_line() here, even though we + // are not interested in the individual sensor readings. + position = read_line(sensors,IR_EMITTERS_ON); + + // The "proportional" term should be 0 when we are on the line. + int proportional = ((int)position) - 2000; + + // Compute the derivative (change) and integral (sum) of the + // position. + int derivative = proportional - last_proportional; + integral += proportional; + + // Remember the last position. + last_proportional = proportional; + + // Compute the difference between the two motor power settings, + // m1 - m2. If this is a positive number the robot will turn + // to the right. If it is a negative number, the robot will + // turn to the left, and the magnitude of the number determines + // the sharpness of the turn. + int power_difference = proportional/20 + integral/10000 + derivative*3/2; + + // Compute the actual motor settings. We never set either motor + // to a negative value. + const int max = 60; + if(power_difference > max) + power_difference = max; + if(power_difference < -max) + power_difference = -max; + + if(sensors[0] >= 500 && sensors[1] >= 250 && sensors[2] >= 500 && sensors[3] >= 250 &&sensors[4] >= 500){ + break; + } + else if (sensors[0] >= 500 && sensors[1] >= 200 && sensors[4] < 100){ + break; + } + else if(sensors[4] >= 500 && sensors[3] >= 200 && sensors[0] < 100){ //for the south and west borders of the grid + break; + } + else if(sensors[4] >= 500 && sensors[3] >= 200 && sensors[2] <100 && sensors[0] < 100){ + break; + } + + else{ + if(power_difference < 0 && (sensors[2] > 100 || sensors[3] > 100 || sensors[1] > 100) ){ + set_motors(max+power_difference, max);} + else if( power_difference > 0 && ( sensors[2] > 100 || sensors[3] > 100 || sensors[1] > 100)){ + set_motors(max, max-power_difference);} + } + } +} + +//coördinates of the orders +void orderOne(){ + order[0].x = 1; //1 + order[0].y = 3; //0 +} + +void orderTwo(){ + order[1].x = 3; //2 + order[1].y = 2; //2 +} + +void orderThree(){ + order[2].x = 1; //0 + order[2].y = 4; //4 +} + +void orderFour(){ + order[3].x = 0; //3 + order[3].y = 0; //1 +} + +//setting coördinate and direction when entering the grid from the maze +void beginLocation(){ + location.x = 4; + location.y = 0; + direction = West; +} + +void turn_North() +{ + clear(); + print("North"); + + switch (direction) + { + case North: + break; + + case East: + grid_rotation_left(); + break; + + case South: + full_rotation(); + break; + + case West: + grid_rotation_right(); + break; + } + direction = North; +} + +void turn_West() +{ + clear(); + print("West"); + + switch (direction) + { + case West: + break; + + case North: + grid_rotation_left(); + break; + + case East: + full_rotation(); + break; + + case South: + grid_rotation_right();; + break; + } + direction = West; +} + +void turn_South() +{ + clear(); + print("South"); + + switch (direction) + { + case South: + break; + + case West: + grid_rotation_left(); + break; + + case North: + full_rotation(); + break; + + case East: + grid_rotation_right();; + break; + } + direction = South; +} + +void turn_East() +{ + clear(); + print("East"); + + switch (direction) + { + case East: + break; + + case South: + grid_rotation_left(); + break; + + case West: + full_rotation(); + break; + + case North: + grid_rotation_right();; + break; + } + direction = East; +} + +void locationMessage(){ + clear(); + print_long(location.x); + print(","); + print_long(location.y); + delay(200); //1000 +} + +void arrivedMessage(){ + clear(); + print("ARRIVED"); +} + +//!UNDER THIS CAN ALL BE TAKEN AWAY, THIS IS USED IN MODE_MAZE & Callibration! + +// Initializes the 3pi, displays a welcome message, calibrates, and +// plays the initial music. +// Initializes the 3pi, displays a welcome message, calibrates, and +// plays the initial music. +void initialize() +{ + unsigned int counter; // used as a simple timer + + // This must be called at the beginning of 3pi code, to set up the + // sensors. We use a value of 2000 for the timeout, which + // corresponds to 2000*0.4 us = 0.8 ms on our 20 MHz processor. + pololu_3pi_init(2000); + load_custom_characters(); // load the custom characters + + // Play welcome music and display a message + print_from_program_space(welcome_line1); + lcd_goto_xy(0,1); + print_from_program_space(welcome_line2); + play_from_program_space(welcome); + delay_ms(1000); + + clear(); + print_from_program_space(demo_name_line1); + lcd_goto_xy(0,1); + print_from_program_space(demo_name_line2); + delay_ms(1000); + + // Display battery voltage and wait for button press + while(!button_is_pressed(BUTTON_B)) + { + int bat = read_battery_millivolts(); + + clear(); + print_long(bat); + print("mV"); + lcd_goto_xy(0,1); + print("Press B"); + + delay_ms(100); + } + + // Always wait for the button to be released so that 3pi doesn't + // start moving until your hand is away from it. + wait_for_button_release(BUTTON_B); + delay_ms(1000); + + // Auto-calibration: turn right and left while calibrating the + // sensors. + for(counter=0;counter<80;counter++) + { + if(counter < 20 || counter >= 60) + set_motors(40,-40); + else + set_motors(-40,40); + + // This function records a set of sensor readings and keeps + // track of the minimum and maximum values encountered. The + // IR_EMITTERS_ON argument means that the IR LEDs will be + // turned on during the reading, which is usually what you + // want. + calibrate_line_sensors(IR_EMITTERS_ON); + + // Since our counter runs to 80, the total delay will be + // 80*20 = 1600 ms. + delay_ms(20); + } + set_motors(0,0); + + // Display calibrated values as a bar graph. + while(!button_is_pressed(BUTTON_B)) + { + // Read the sensor values and get the position measurement. + unsigned int position = read_line(sensors,IR_EMITTERS_ON); + + // Display the position measurement, which will go from 0 + // (when the leftmost sensor is over the line) to 4000 (when + // the rightmost sensor is over the line) on the 3pi, along + // with a bar graph of the sensor readings. This allows you + // to make sure the robot is ready to go. + clear(); + print_long(position); + lcd_goto_xy(0,1); + display_readings(sensors); + + delay_ms(100); + } + wait_for_button_release(BUTTON_B); + + clear(); + + print("Go!"); + + // Play music and wait for it to finish before we start driving. + play_from_program_space(go); + while(is_playing()); +} + +// This function loads custom characters into the LCD. Up to 8 +// characters can be loaded; we use them for 7 levels of a bar graph. +void load_custom_characters() +{ + lcd_load_custom_character(levels+0,0); // no offset, e.g. one bar + lcd_load_custom_character(levels+1,1); // two bars + lcd_load_custom_character(levels+2,2); // etc... + lcd_load_custom_character(levels+3,3); + lcd_load_custom_character(levels+4,4); + lcd_load_custom_character(levels+5,5); + lcd_load_custom_character(levels+6,6); + clear(); // the LCD must be cleared for the characters to take effect +} + +// This function displays the sensor readings using a bar graph. +void display_readings(const unsigned int *calibrated_values) +{ + unsigned char i; + + for(i=0;i<5;i++) { + // Initialize the array of characters that we will use for the + // graph. Using the space, an extra copy of the one-bar + // character, and character 255 (a full black box), we get 10 + // characters in the array. + const char display_characters[10] = {' ',0,0,1,2,3,4,5,6,255}; + + // The variable c will have values from 0 to 9, since + // calibrated values are in the range of 0 to 1000, and + // 1000/101 is 9 with integer math. + char c = display_characters[calibrated_values[i]/101]; + + // Display the bar graph character. + print_character(c); + } +} + +void full_rotation(){ + set_motors(0,0); + delay_ms(500); + set_motors(60,-60); + delay_ms(540); + set_motors(0,0); + position = read_line(sensors,IR_EMITTERS_ON); + delay_ms(500); +} |