diff options
Diffstat (limited to 'robot/readme.md')
| -rw-r--r-- | robot/readme.md | 35 |
1 files changed, 18 insertions, 17 deletions
diff --git a/robot/readme.md b/robot/readme.md index 4a7aca3..9f10bcc 100644 --- a/robot/readme.md +++ b/robot/readme.md @@ -52,17 +52,22 @@ handling module, which then both handles the error and forwards it to pc communication for logging purposes). here's a quick run-down of all modules and what they're supposed to do: -|module |internal name|author|purpose| -|----------------|-------------|-|-| -|hypervisor |`hypervisor `|N/a| backbone of all other modules; stores global variables; controls when other modules run| -|pc communication|`sercomm `|Fiona| reads and parses incoming serial data; sends all data in the message buffer| -|error handling |`errcatch `|Loek| receives error codes; controls how errors are handled| -|i/o read & write|`io `|Jorn & Abdullaahi| reads all inputs to global state; writes all outputs| -|mode logic |`modes `|N/a| executes the appropriate module for current mode| -|maze |`mode_maze `|Jorn & Abdullaahi| controls robot during maze portion of map; hands off control to warehouse module| -|warehouse |`mode_grid `|Loek| controls robot during warehouse portion of map; hands off control to maze module| -|emergency stop |`mode_halt `|Fiona| stops all execution until emergency mode is reset by software or user| -|calibration |`mode_calb `|Fiona| find line by turning on own axis if lost| +|module |internal name |author|purpose| +|------------------|--------------|-|-| +|hypervisor |`hypervisor `|N/a| backbone of all other modules; stores global variables; controls when other modules run| +|pc communication |`sercomm `|Fiona| reads and parses incoming serial data; sends all data in the message buffer| +|error handling |`errcatch `|Loek| receives error codes; controls how errors are handled| +|i/o read & write |`io `|Jorn & Abdullaahi| reads all inputs to global state; writes all outputs| +|mode logic |`modes `|N/a| executes the appropriate module for current mode| +|maze |`mode_maze `|Jorn & Abdullaahi| controls robot during maze portion of map; hands off control to warehouse module| +|warehouse |`mode_grid `|Loek| controls robot during warehouse portion of map; hands off control to maze module| +|emergency stop |`mode_halt `|Fiona| stops all execution until emergency mode is reset by software or user| +|line finding |`mode_calb `|Fiona| find line by turning on own axis if lost| +|charge station |`mode_charger`|TBD| go to the charging station transition in the grid, and continue until a black circle is found| +|direct control |`mode_directc`|TBD| respond to [DIRC](../protocol.md#DIRC) commands| +|wet floor |`mode_spin `|TBD| spin uncontrollably (simulating wet floor??)| +|sensor calibration|`mode_senscal`|TBD| calibrate underside uv sensors| + ## some standards @@ -100,16 +105,12 @@ this list will probably get updated from time to time: global todo: -- [ ] add test/simulation mode for wet floor (spinning) -- [ ] add a manual control mode - [ ] start robot in calibration mode - [ ] assume robot starts in maze - [ ] maze-grid transition detection in seperate file (used by grid and maze mode) -- [ ] clear global timer at start of cycle instead of just for mode selection - module (for last ping time measurement) -- [ ] calibrate (line-detecting) light sensors in setup.c, or manually by - placing the robot and pressing a button (maybe make this a seperate mode) +- [ ] calibrate (line-detecting) light sensors manually by placing the robot + and pressing a button (maybe make this a seperate mode) ### hypervisor |